mupen64plus.cfg – certain settings not working

Home Forums RetroPie Project Everything else related to the RetroPie Project mupen64plus.cfg – certain settings not working

RetroPie has a new website and forum. Please visit https://retropie.org.uk/ for the new site. The new forum is located at https://retropie.org.uk/forum/. This forum is left here as a read-only archive.

This topic contains 0 replies, has 1 voice, and was last updated by Profile photo of recurzion recurzion 2 years, 4 months ago.

Viewing 1 post (of 1 total)
  • Author
    Posts
  • #83690
    Profile photo of recurzion
    recurzion
    Participant

    Hi there,

    I’m editing the mupen64plus.cfg file under ~/.config/mupen64plus/ and I can’t get the resolution to change (by changing ScreenWidth and ScreenHeight under [Video-General]). Also, Joy Mapping Stop isn’t working either. I set it equal to “j0b9” after confirming using jstest that the button I want is button 9 on joystick 0.

    Does anyone have any advice/input on this? My config file is below:

    
    # Mupen64Plus Configuration File
    # This file is automatically read and written by the Mupen64Plus Core library
    
    [Audio-OMX]
    
    # Mupen64Plus OMX Audio Plugin config parameter version number
    Version = 1
    # Frequency which is used if rom doesn't want to change it
    DEFAULT_FREQUENCY = 33600
    # Swaps left and right channels
    SWAP_CHANNELS = False
    # Audio output to go to (0) Analogue jack, (1) HDMI
    OUTPUT_PORT = 1
    # Audio Output Frequncy mode: 0 = Rom Frequency, 1 ROM Frequency if supported (HDMI only), 2 = Standard frequency < Rom Frequency, 3 = Standard frequency > Rom Frequency, [N] Force output frequency
    DEFAULT_MODE = 0
    
    [Core]
    
    # Mupen64Plus Core config parameter set version number.  Please don't change this version number.
    Version = 1.010000
    # Draw on-screen display if True, otherwise don't draw OSD
    OnScreenDisplay = True
    # Use Pure Interpreter if 0, Cached Interpreter if 1, or Dynamic Recompiler if 2 or more
    R4300Emulator = 2
    # Disable compiled jump commands in dynamic recompiler (should be set to False)
    NoCompiledJump = False
    # Disable 4MB expansion RAM pack. May be necessary for some games
    DisableExtraMem = False
    # Increment the save state slot after each save operation
    AutoStateSlotIncrement = False
    # Activate the R4300 debugger when ROM execution begins, if core was built with Debugger support
    EnableDebugger = False
    # Save state slot (0-9) to use when saving/loading the emulator state
    CurrentStateSlot = 0
    # Path to directory where screenshots are saved. If this is blank, the default value of ${UserConfigPath}/screenshot will be used
    ScreenshotPath = ""
    # Path to directory where emulator save states (snapshots) are saved. If this is blank, the default value of ${UserConfigPath}/save will be used
    SaveStatePath = ""
    # Path to directory where SRAM/EEPROM data (in-game saves) are stored. If this is blank, the default value of ${UserConfigPath}/save will be used
    SaveSRAMPath = ""
    # Path to a directory to search when looking for shared data files
    SharedDataPath = ""
    # Scheduling policy. 0 for Standard (SCHED_OTHER), 1-99 RealTime FIFO policy with Priority of [N]
    Scheduler = 10
    
    [CoreEvents]
    
    # Mupen64Plus CoreEvents config parameter set version number.  Please don't change this version number.
    Version = 1
    # SDL keysym for stopping the emulator
    Kbd Mapping Stop = 27
    # SDL keysym for switching between fullscreen/windowed modes
    Kbd Mapping Fullscreen = 323
    # SDL keysym for saving the emulator state
    Kbd Mapping Save State = 286
    # SDL keysym for loading the emulator state
    Kbd Mapping Load State = 288
    # SDL keysym for advancing the save state slot
    Kbd Mapping Increment Slot = 0
    # SDL keysym for resetting the emulator
    Kbd Mapping Reset = 290
    # SDL keysym for slowing down the emulator
    Kbd Mapping Speed Down = 291
    # SDL keysym for speeding up the emulator
    Kbd Mapping Speed Up = 292
    # SDL keysym for taking a screenshot
    Kbd Mapping Screenshot = 293
    # SDL keysym for pausing the emulator
    Kbd Mapping Pause = 112
    # SDL keysym for muting/unmuting the sound
    Kbd Mapping Mute = 109
    # SDL keysym for increasing the volume
    Kbd Mapping Increase Volume = 93
    # SDL keysym for decreasing the volume
    Kbd Mapping Decrease Volume = 91
    # SDL keysym for temporarily going really fast
    Kbd Mapping Fast Forward = 102
    # SDL keysym for advancing by one frame when paused
    Kbd Mapping Frame Advance = 47
    # SDL keysym for pressing the game shark button
    Kbd Mapping Gameshark = 103
    # Joystick event string for stopping the emulator
    Joy Mapping Stop = "j0b9"
    # Joystick event string for switching between fullscreen/windowed modes
    Joy Mapping Fullscreen = ""
    # Joystick event string for saving the emulator state
    Joy Mapping Save State = ""
    # Joystick event string for loading the emulator state
    Joy Mapping Load State = ""
    # Joystick event string for advancing the save state slot
    Joy Mapping Increment Slot = ""
    # Joystick event string for taking a screenshot
    Joy Mapping Screenshot = ""
    # Joystick event string for pausing the emulator
    Joy Mapping Pause = ""
    # Joystick event string for muting/unmuting the sound
    Joy Mapping Mute = ""
    # Joystick event string for increasing the volume
    Joy Mapping Increase Volume = ""
    # Joystick event string for decreasing the volume
    Joy Mapping Decrease Volume = ""
    # Joystick event string for fast-forward
    Joy Mapping Fast Forward = ""
    # Joystick event string for pressing the game shark button
    Joy Mapping Gameshark = ""
    
    [Input-SDL-Control1]
    
    # Mupen64Plus SDL Input Plugin config parameter version number.  Please don't change this version number.
    version = 2
    # Controller configuration mode: 0=Fully Manual, 1=Auto with named SDL Device, 2=Fully automatic
    mode = 2
    # Specifies which joystick is bound to this controller: -1=No joystick, 0 or more= SDL Joystick number
    device = 0
    # SDL joystick name (or Keyboard)
    name = "Jess Technology Co., Ltd. 3 IN 1 Conversion-Box"
    # Specifies whether this controller is 'plugged in' to the simulated N64
    plugged = True
    # Specifies which type of expansion pak is in the controller: 1=None, 2=Mem pak, 5=Rumble pak
    plugin = 2
    # If True, then mouse buttons may be used with this controller
    mouse = False
    # Scaling factor for mouse movements.  For X, Y axes.
    MouseSensitivity = "2.00,2.00"
    # The minimum absolute value of the SDL analog joystick axis to move the N64 controller axis value from 0.  For X, Y axes.
    AnalogDeadzone = "4096,4096"
    # An absolute value of the SDL joystick axis >= AnalogPeak will saturate the N64 controller axis value (at 80).  For X, Y axes. For each axis, this must be greater than the corresponding AnalogDeadzone value
    AnalogPeak = "32768,32768"
    # Digital button configuration mappings
    DPad R = "hat(0 Right)"
    DPad L = "hat(0 Left)"
    DPad D = "hat(0 Down)"
    DPad U = "hat(0 Up)"
    Start = "button(8)"
    Z Trig = "button(10)"
    B Button = "button(5)"
    A Button = "button(2)"
    C Button R = "button(1)"
    C Button L = "button(3)"
    C Button D = "button(11)"
    C Button U = "button(0)"
    R Trig = "button(7)"
    L Trig = "button(6)"
    Mempak switch = ""
    Rumblepak switch = ""
    # Analog axis configuration mappings
    X Axis = "axis(0-,0+)"
    Y Axis = "axis(1-,1+)"
    
    [Input-SDL-Control2]
    
    # Mupen64Plus SDL Input Plugin config parameter version number.  Please don't change this version number.
    version = 2
    # Controller configuration mode: 0=Fully Manual, 1=Auto with named SDL Device, 2=Fully automatic
    mode = 2
    # Specifies which joystick is bound to this controller: -1=No joystick, 0 or more= SDL Joystick number
    device = -1
    # SDL joystick name (or Keyboard)
    name = ""
    # Specifies whether this controller is 'plugged in' to the simulated N64
    plugged = False
    # Specifies which type of expansion pak is in the controller: 1=None, 2=Mem pak, 5=Rumble pak
    plugin = 1
    # If True, then mouse buttons may be used with this controller
    mouse = False
    # Scaling factor for mouse movements.  For X, Y axes.
    MouseSensitivity = "2.00,2.00"
    # The minimum absolute value of the SDL analog joystick axis to move the N64 controller axis value from 0.  For X, Y axes.
    AnalogDeadzone = "4096,4096"
    # An absolute value of the SDL joystick axis >= AnalogPeak will saturate the N64 controller axis value (at 80).  For X, Y axes. For each axis, this must be greater than the corresponding AnalogDeadzone value
    AnalogPeak = "32768,32768"
    # Digital button configuration mappings
    DPad R = ""
    DPad L = ""
    DPad D = ""
    DPad U = ""
    Start = ""
    Z Trig = ""
    B Button = ""
    A Button = ""
    C Button R = ""
    C Button L = ""
    C Button D = ""
    C Button U = ""
    R Trig = ""
    L Trig = ""
    Mempak switch = ""
    Rumblepak switch = ""
    # Analog axis configuration mappings
    X Axis = ""
    Y Axis = ""
    
    [Input-SDL-Control3]
    
    # Mupen64Plus SDL Input Plugin config parameter version number.  Please don't change this version number.
    version = 2
    # Controller configuration mode: 0=Fully Manual, 1=Auto with named SDL Device, 2=Fully automatic
    mode = 2
    # Specifies which joystick is bound to this controller: -1=No joystick, 0 or more= SDL Joystick number
    device = -1
    # SDL joystick name (or Keyboard)
    name = ""
    # Specifies whether this controller is 'plugged in' to the simulated N64
    plugged = False
    # Specifies which type of expansion pak is in the controller: 1=None, 2=Mem pak, 5=Rumble pak
    plugin = 1
    # If True, then mouse buttons may be used with this controller
    mouse = False
    # Scaling factor for mouse movements.  For X, Y axes.
    MouseSensitivity = "2.00,2.00"
    # The minimum absolute value of the SDL analog joystick axis to move the N64 controller axis value from 0.  For X, Y axes.
    AnalogDeadzone = "4096,4096"
    # An absolute value of the SDL joystick axis >= AnalogPeak will saturate the N64 controller axis value (at 80).  For X, Y axes. For each axis, this must be greater than the corresponding AnalogDeadzone value
    AnalogPeak = "32768,32768"
    # Digital button configuration mappings
    DPad R = ""
    DPad L = ""
    DPad D = ""
    DPad U = ""
    Start = ""
    Z Trig = ""
    B Button = ""
    A Button = ""
    C Button R = ""
    C Button L = ""
    C Button D = ""
    C Button U = ""
    R Trig = ""
    L Trig = ""
    Mempak switch = ""
    Rumblepak switch = ""
    # Analog axis configuration mappings
    X Axis = ""
    Y Axis = ""
    
    [Input-SDL-Control4]
    
    # Mupen64Plus SDL Input Plugin config parameter version number.  Please don't change this version number.
    version = 2
    # Controller configuration mode: 0=Fully Manual, 1=Auto with named SDL Device, 2=Fully automatic
    mode = 2
    # Specifies which joystick is bound to this controller: -1=No joystick, 0 or more= SDL Joystick number
    device = -1
    # SDL joystick name (or Keyboard)
    name = ""
    # Specifies whether this controller is 'plugged in' to the simulated N64
    plugged = False
    # Specifies which type of expansion pak is in the controller: 1=None, 2=Mem pak, 5=Rumble pak
    plugin = 1
    # If True, then mouse buttons may be used with this controller
    mouse = False
    # Scaling factor for mouse movements.  For X, Y axes.
    MouseSensitivity = "2.00,2.00"
    # The minimum absolute value of the SDL analog joystick axis to move the N64 controller axis value from 0.  For X, Y axes.
    AnalogDeadzone = "4096,4096"
    # An absolute value of the SDL joystick axis >= AnalogPeak will saturate the N64 controller axis value (at 80).  For X, Y axes. For each axis, this must be greater than the corresponding AnalogDeadzone value
    AnalogPeak = "32768,32768"
    # Digital button configuration mappings
    DPad R = ""
    DPad L = ""
    DPad D = ""
    DPad U = ""
    Start = ""
    Z Trig = ""
    B Button = ""
    A Button = ""
    C Button R = ""
    C Button L = ""
    C Button D = ""
    C Button U = ""
    R Trig = ""
    L Trig = ""
    Mempak switch = ""
    Rumblepak switch = ""
    # Analog axis configuration mappings
    X Axis = ""
    Y Axis = ""
    
    [UI-Console]
    
    # Mupen64Plus UI-Console config parameter set version number.  Please don't change this version number.
    Version = 1
    # Directory in which to search for plugins
    PluginDir = "./"
    # Filename of video plugin
    VideoPlugin = "mupen64plus-video-rice.so"
    # Filename of audio plugin
    AudioPlugin = "mupen64plus-audio-omx.so"
    # Filename of input plugin
    InputPlugin = "mupen64plus-input-sdl.so"
    # Filename of RSP plugin
    RspPlugin = "mupen64plus-rsp-hle.so"
    
    [Video-General]
    
    # Use fullscreen mode if True, or windowed mode if False
    Fullscreen = False
    # Width of output window or fullscreen width
    ScreenWidth = 1024
    # Height of output window or fullscreen height
    ScreenHeight = 768
    # If true, activate the SDL_GL_SWAP_CONTROL attribute
    VerticalSync = False
    
    [Video-Rice]
    
    # Frame Buffer Emulation (0=ROM default, 1=disable)
    FrameBufferSetting = 0
    # Frequency to write back the frame buffer (0=every frame, 1=every other frame, etc)
    FrameBufferWriteBackControl = 0
    # Render-to-texture emulation (0=none, 1=ignore, 2=normal, 3=write back, 4=write back and reload)
    RenderToTexture = 0
    # Control when the screen will be updated (0=ROM default, 1=VI origin update, 2=VI origin change, 3=CI change, 4=first CI change, 5=first primitive draw, 6=before screen clear, 7=after screen drawn)
    ScreenUpdateSetting = 4
    # Force to use normal alpha blender
    NormalAlphaBlender = True
    # Use a faster algorithm to speed up texture loading and CRC computation
    FastTextureLoading = False
    # Use different texture coordinate clamping code
    AccurateTextureMapping = True
    # Force emulated frame buffers to be in N64 native resolution
    InN64Resolution = False
    # Try to reduce Video RAM usage (should never be used)
    SaveVRAM = False
    # Enable this option to have better render-to-texture quality
    DoubleSizeForSmallTxtrBuf = False
    # Force to use normal color combiner
    DefaultCombinerDisable = False
    # Enable game-specific settings from INI file
    EnableHacks = True
    # If enabled, graphics will be drawn in WinFrame mode instead of solid and texture mode
    WinFrameMode = False
    # N64 Texture Memory Full Emulation (may fix some games, may break others)
    FullTMEMEmulation = False
    # Enable vertex clipper for fog operations
    OpenGLVertexClipper = False
    # Enable/Disable SSE optimizations for capable CPUs
    EnableSSE = False
    # Use GPU vertex shader
    EnableVertexShader = True
    # If this option is enabled, the plugin will skip every other frame
    SkipFrame = True
    # If this option is enabled, the plugin will only draw every other screen update
    SkipScreenUpdate = True
    # If enabled, texture enhancement will be done only for TxtRect ucode
    TexRectOnly = False
    # If enabled, texture enhancement will be done only for textures width+height<=128
    SmallTextureOnly = False
    # Select hi-resolution textures based only on the CRC and ignore format+size information (Glide64 compatibility)
    LoadHiResCRCOnly = True
    # Enable hi-resolution texture file loading
    LoadHiResTextures = False
    # Enable texture dumping
    DumpTexturesToFiles = False
    # Display On-screen FPS
    ShowFPS = True
    # Use Mipmapping? 0=no, 1=nearest, 2=bilinear, 3=trilinear
    Mipmapping = 0
    # Enable, Disable or Force fog generation (0=Disable, 1=Enable n64 choose, 2=Force Fog)
    FogMethod = 0
    # Force to use texture filtering or not (0=auto: n64 choose, 1=force no filtering, 2=force filtering)
    ForceTextureFilter = 1
    # Primary texture enhancement filter (0=None, 1=2X, 2=2XSAI, 3=HQ2X, 4=LQ2X, 5=HQ4X, 6=Sharpen, 7=Sharpen More, 8=External, 9=Mirrored)
    TextureEnhancement = 0
    # Secondary texture enhancement filter (0 = none, 1-4 = filtered)
    TextureEnhancementControl = 0
    # Color bit depth to use for textures (0=default, 1=32 bits, 2=16 bits)
    TextureQuality = 0
    # Z-buffer depth (only 16 or 32)
    OpenGLDepthBufferSetting = 32
    # Enable/Disable MultiSampling (0=off, 2,4,8,16=quality)
    MultiSampling = 0
    # Color bit depth for rendering window (0=32 bits, 1=16 bits)
    ColorQuality = 0
    # OpenGL level to support (0=auto, 1=OGL_1.1, 2=OGL_1.2, 3=OGL_1.3, 4=OGL_1.4, 5=OGL_1.4_V2, 6=OGL_TNT2, 7=NVIDIA_OGL, 8=OGL_FRAGMENT_PROGRAM)
    OpenGLRenderSetting = 0
    # Enable/Disable Anisotropic Filtering for Mipmapping (0=no filtering, 2-16=quality). This is uneffective if Mipmapping is 0. If the given value is to high to be supported by your graphic card, the value will be the highest value your graphic card can support. Better result with Trilinear filtering
    AnisotropicFiltering = 0
    
    

Viewing 1 post (of 1 total)

Forums are currently read only - please visit the new RetroPie forums at https://retropie.org.uk/forums/

Skip to toolbar